Sunday, June 16, 2013

Journey of the Boardwalk: Part 30 - FNHON Handlepost (双钉)

Finally, I have the chance to blog about the latest upgrade for my Dahon Boardwalk Di2. Right after I changed the handlepost for the Vitesse, I also changed the handlepost for my Boardwalk. You may have known that my Boardwalk handlepost was upgraded quite sometime ago, from the stock adjustable handlepost to a one-piece handlepost.

Recently I came across the Fnhon range of handleposts, which has a wide variety of lengths and designs to cater to most handlebar requirements. Besides taking the chance to upgrade the handlepost on the Vitesse, I also found a new handlepost for my Boardwalk. Let us take a closer look at the new Fnhon handlepost for my Boardwalk.

New Fnhon handlepost, in black. Can you see what is the difference?

Different clamp design for the handlebar. This uses a 2 bolt design to secure the handlebar, very similar to normal road/MTB stems.

This new handlebar clamp design is why I decided to try the new Fnhon handlebar. I find that I don't adjust the QR clamp on the handlepost at all, since I don't need to rotate the handlebar when folding the bike. With a QR clamp, the clamp lever is actually quite long and restricts the position of my handlebar extension mount. Thus it is better for me to use this 2 bolt design as it looks less bulky and allows me to clamp the handlebar properly with an Allen key, without it slipping.

  Same designs as described on the other Fnhon handlepost blog post.

Applying some grease on the sliding surfaces of the clamp will make it easier to achieve a proper clamping force and also avoid creaking sounds.

After I removed the Mu Uno handlepost, I decided to compare the two handleposts side by side before installing the new Fnhon handlepost.

The new Fnhon handlepost is shorter than the Mu Uno handlepost

The Fnhon handlepost (31.5cm) that I chose is 5 cm shorter than the Dahon Mu Uno handlepost. Also note the different handlebar clamp designs.

The Mu Uno handlepost is rather long, and weighs 635 grams. Still lighter than the weight of the stock adjustable handlepost (752 grams).

The new Fnhon handlepost weighs 524 grams, more than 100 grams lighter than the Mu Uno handlepost. An added bonus!

Before: Mu Uno handlepost. Note that the handlepost is quite a bit higher than the saddle. Good for comfort but hard to get low for speed.

After: Fnhon 31.5cm handlepost. The handlepost is now at the same level as the saddle.

 With the elimination of the QR clamp on the previous handlepost, the stem area is now much cleaner and neater.

Without the QR lever in the way, the Di2 display can now be placed lower for a neater cockpit.

 Side view. I like the clean look of the new 2 bolt clamp design on the Fnhon handlepost. In fact they have just come up with a 4 bolt clamp design that is stiffer, but the length is too short for me.

By changing from the Mu Uno handlepost to the Fnhon handlepost, there are a few differences:
1) Weight reduction of 100+ grams.
2) Cleaner stem area from the elimination of the QR clamp.
3) Shorter handlepost (5 cm shorter) for a more sporty riding position.
4) Stiffer handlepost due to the shorter length of the handlepost.

After 100km of test riding with the new Fnhon handlepost and the new, lower riding position, I am quite happy with the upgrade. Initially I was not used to the lower riding position, since I have been using the Mu Uno handlepost for more than 2 years. A 5 cm reduction in height is actually quite a lot and the different riding position is very obvious. On the plus side, I like the new sportier position, and an added benefit is that the handlepost is stiffer since it is shorter, and I can now pull on the handlepost for added power.

I also find myself holding the top of the handlebar more often, when I want to ride in a more relaxed position. With the secondary brake levers and Di2 satellite shifters, I can stay in the more relaxed position for as long as I want, without sacrificing any brake or shifting functions. It is like riding both a drop bar and a flat handlebar road bike at the same time.

A minor problem which I detected during riding is that the brake cable overlaps the secondary brake lever. This is because when I changed to the lower handlepost height, I did not trim and shorten the cables. I will need to find time to shorten the brake cables.

Brake cables are now too long since the handlepost height has been reduced.

More sporty riding position!

Another view of the bike

Looks all ready to chiong!

One word of caution is that if you do get a Fnhon handlepost, you will likely have to change the handlepost yourself, as the bike shop would probably not service and install the Fnhon handlepost for you. That said, it is not very difficult, and you can refer to this installation guide. Also, changing to alternative components is always at your own risk, as this is not an official Dahon part which may be covered under warranty.


  1. Hi steve, can a fnhon handlepost fit a tern link p9? Thinking to switch to dropbar config but not keen to get the tern T handlepost cos its too tall; adding a stem to lower the drop seems clunky and I prefer not to. Thx!

    1. You will need a headset top cap and cut the steerer tube. I wouldn't change the handlepost, as the Tern handlepost is much stiffer. I think the X10 or X20 handlepost is shorter.

  2. Hi, really interested in all your handlebar mods. I am about to make some changes to my daughter's Ridgeback, Dahon clone, but am wondering how tall you are since 31.5cm is much shorter post than on her bike. Thanks Gerry

    1. I am about 170cm tall. Not sure if the Ridgeback can use the Dahon handlepost.

  3. Hi Steve
    I am thinking of replacing my Dahon handlepost with a Tern Physis. In your view, would that be an easy swap? Thanks.

    1. It is not possible as the handlepost and headset design are different. The Physis handlepost requires a longer steerer tube which the Daon fork does not have. Headset construction is different too.

  4. Hi Steve,

    I have been lurking on your site for a while and recently I finally purchased a folding bike for myself. It is a 2015 Dahon Boardwalk D8. I find that I have a problem with the fit on longer rides as the handlebar is too low (I am also 170cm).

    I am looking for options and wondering whether I should get a longer handlepost or a riser bar. Unfortunately I will need a quick release clamp as the bike doesn't (seem to?) fold nicely if I don't point the brake levers at a certain angle. I happen to fold up my bike everyday when I reach the office so foldabillity is quite a big factor for me.

    Do you have any suggestions? Many thanks in advance!

    1. There are a few longer Fnhon handleposts with a qr. You can search for them on

    2. Thank you for the direction. I shall check it out!

      I also tried your method of folding and my bike still manages to fit into the Doppelganger carrier I got quite nicely.I guess it should work too if I get a riser bar?

      Also, my current handlepost is not adjustable (different from your stock?) and I have no idea how much it weighs. The Dahon website isn't helpful either. I don't have a reference weight I should be looking at for a new handlepost. Do you suggest I take it apart and try to weigh it or is there a better solution?

    3. The stock handlepost on the 2015 Boardwalk D8 looks very much like a Mu Uno handlepost, which weighs 660 grams. You can search for Mu Uno handlepost on my blog for more info and pictures.

      This is already a long handlepost and i don't suggest getting an even longer one. A tall handlebar will be less stable, and you will look like you are riding a Harley motor bike.

    4. Actually I rode 15km today and had raised my saddle higher (after getting more confident with the bike). The handlepost height did not feel as bad anymore. Maybe I was just not used to riding a folding bike sort of geometry previously.

      I guess I will wait a while first before upgrading anything. I am swapping out the tubes and tires for Kojaks and light weight Schwalbe though.

  5. Hi Steve,

    Is it normal for Fnhon handlepost to be very tight when you install into the front fork? I can't insert the handlepost into the front fork. Seems like need to sand a little on the fork tube.

    1. It is normally OK. You can try inserting a flat blade screwdriver into the gap between the clamping faces of the handlepost base, and twisting it to open up the clamp slightly before placing onto the steerer tube.